Job Responsibilities:

1. Prepared product outline design and detailed design;

2. Participate in structural design, guide and review PCB design;

3. Design and debug the hardware of industrial switches in special industries such as electric power, Safe city, intelligent transportation and rail transit;

4. Promote product testing, review test plans, and solve problems found in testing;

5. Archive, release and maintain product data, solve problems in mass production and customer use;

6. Participate in the selection of new devices and the formulation of new schemes;

7. Guided to complete the upgrade and improvement of existing products;

Qualifications:

1. Full-time bachelor degree or above, major in communication, electronics, computer or related;

2. Familiar with 23-bit processor architecture, familiar with the working principle of Arm7, STM32 and other processors, with 2-3 years of development experience in Ethernet switching products or industrial communication;

3. Strong learning ability, strong pressure resistance ability, certain document writing ability, able to reasonably deal with various problems encountered in the work.

4. EMC design modification experience is preferred.

Job Responsibilities:

1. Responsible for the development of network applications of equipment networking products;

2. Responsible for the development of industrial communication interface application programs for equipment networking products;

3. Responsible for Linux driver development of device networking products;

4. Responsible for the development and maintenance of Linux system platform for devices connected to the Internet;

Qualifications:

1. College degree or above (bachelor degree preferred), majored in electronics, communication, automation, computer, software engineering or related;

2.  Proficient in C language programming, good programming habits and skills, 3-5 years of experience in embedded Linux application and driver development, with Linux application and network development capabilities;

3. Proficient in TCP/IP protocol, familiar with UDP, TCP programming, familiar with embedded Web Server.

4. Proficient in programming common communication interfaces such as serial port, CAN, IO and Ethernet;

5. Strong sense of responsibility and teamwork spirit, able to work under pressure.

6. Good English reading and communication skills.

7. Experience in serial port server, CAN server, Modbus gateway and IO server is preferred.

Job Responsibilities:

1. Engaged in the development and maintenance of switch layer 2 / Layer 3 protocol software；

Qualifications:

1. Bachelor degree or above in electronics, communication and computer related majors;

2. Proficient in Linux or other embedded system C language programming and familiar with embedded operating system;

3. Familiar with TCP/IP protocol stack, good software development foundation;

4. More than 3 years working experience in embedded software development, with Ethernet switch/router protocol software development experience preferred;

5. Experience in MSTP, LACP, Rip/OSPF/ BGP protocol development is preferred; strong ability to analyze and solve problems is preferred;

6. Good communication and teamwork skills.
 

Job Responsibilities：

1. Wrote and maintained the edge computing gateway test cases, reviewed and checked the test cases;

2. Collect test requirements and decompose test tasks. Overall test plan preparation, software and hardware test plan preparation, integration test plan preparation;

3. Develop test strategy and test risk assessment;

4. Pre-developed new product line and new function test development, test scheme, use case execution, etc.;

5. TCU software platform test and product test;

6. Wrote test reports, submitted and tracked bugs;

7. New employee training, establishment and maintenance of industrial laboratory platform, and management of laboratory equipment;

8. Handle other transactional work arranged by leaders.

Qualifications:

1. Full-time bachelor degree or above, electrical automation major is preferred, good English level, CET4 or above;

2. Familiar with network communication equipment (switch, router, test experience);

3. Familiar with Internet of Things interface protocol (MQTT, RestfuloPC-UA)

4. Familiar with common industrial fieldbus protocols (Profibus, CANOPEN, Profinet, EthernetIP, EtherCAT)

5. Familiar with PLC configuration, ladder diagram and ST programming.

6. Proficient in TCPIP protocol (such as ARP, ICMP, TCP, UDP, etc.);

7. Strong problem analysis ability, overall planning ability, and strong subjective initiative;

8. Good at communication, good at understanding, strong learning ability, teamwork spirit and sense of responsibility;

9. Familiar with LINUX shell language is preferred;

10. Certain management ability or relevant management experience is preferred.

Job Responsibilities:

1. Analysis, judgment and maintenance of defective products returned by customers;

2. Product exception handling and difficulty board analysis;

3. Completing other daily work of the department.

Qualifications:

1. Male, 18-35 years old, 2 years or above experience in maintenance of COMPUTER motherboard, graphics card, server and other PCB boards;

2. Good health, no bad habits, serious, patient, no communication barriers;

3. Have the knowledge of electronic circuit, can understand the circuit schematic diagram, basic EDA software operation;

4. Proficient in welding, skilled in the use of electric soldering iron, hot air gun, multimeter, chip burner and other maintenance tools;

5. Willing to study maintenance technology, hard-working, can accept a certain degree of overtime;

6. Mastering BGA welding technology is preferred.

Job Responsibilities:

1. Responsible for direction control, industry planning and market strategy of the industrial Internet industry (intelligent manufacturing).

2. Responsible for brand promotion and relevant Marketing of the industry.

3. Responsible for the overall performance of the industry, complete the annual performance target, and decompose the performance into monthly and quarterly assessment.

4. Responsible for the follow-up and implementation of key KP and KA in the industry.

5. Establish the industrial Internet industry circle and complete the top-level design.

6. Responsible for visiting and following up key resources in the industry, such as owners, design institutes and general contractors.

7. Responsible for market demand research, industry product planning, industry internal and external training, etc.

Qualifications:

1. Bachelor degree or above, major in electronics, computer, information and communication, marketing, master degree is preferred.

2. At least 3 years market management or technology management experience in industrial Internet, intelligent industry, familiar with the industry circle.

3. With sensitive business and market awareness, strong ability to analyze and solve problems, with excellent resource integration ability and industry promotion ability.

4. Good communication and cooperation skills and rich team management experience.

5. Excellent industry operation and overall management ability.

Job Responsibilities:

1. Responsible for market development and customer maintenance of industrial switch products;

2. Responsible for product publicity, promotion and sales, and complete the sales target;

3. Collect and search customer information, established customer files, visit customers and develop new customers as planned;

4. Complete other tasks assigned by the company.

Qualifications:

1. College degree or above, majored in automation, computer network communication, etc.;

2. Experience in industrial communication products.

3. Strong customer development ability, market insight and project follow-up ability;

4. Good at planning and summarizing, outgoing, easy to communicate, good teamwork spirit;